 |
| CFYUSEU Crypto Ethereum Miner Case with Barebone Motherboard |
CFYUSEU Mining Rig Frame 8 x 70mm GPU Slots with 8 Fans, Crypto Ethereum Miner Case with Abstract Motherboard for ETH/ZEC, Cryptocurrency System Machine with SSD/RAM (Without GPU/PSU)
1. Please use a GPU smaller than 32cm. The platform is compatible with a single-channel power supply. Please make sure that your power supply is a single channel power supply.
2. If you are using a 2000W power adapter:
After GPU overclocking is enabled, it becomes easy to copy the motherboard, power supply, and GPU. A GPU with a lower power supply rating is recommended. For example, if you're running a 3090/3080, the rated power of the 3090 is 290 watts and the GPU's overclocking power is about 350 watts. We recommend 4 GPUs. Just run 3070 and 3060 8 yuan. Please reserve 400 watts for other consumption
3. A mining machine is a unit that needs technology. If you have any technical problem, please contact us, we will be glad to solve your problem.
Excavator problem identification:
We did a quick test before shipping. There is a problem with the drilling options, probably because of the long-distance transportation and heavy express delivery. Do not turn on the GPU immediately after receiving the device. Let's see if the drilling rig works first.
1. Power supply troubleshooting
Check the power supply to see if the fan is spinning.
2. Motherboard troubleshooting
Connect the keyboard to the computer and press the Num Lock key on the keyboard. If the light does not light up, the motherboard may be defective. If the Num Lock indicator is on and you press it again, the Num Lock indicator will turn off, indicating that there is no problem with the motherboard.
More tips
1. System installation
The MSATA SSD we configured with the system will not be installed, you can contact the relevant system official website to download it, there is an installation tutorial.
2. The BIOS can't be called
The HDMI cable is not compatible with the HDMI port. Please replace the HDMI cable.
3. The GPU cannot be recognized
You need to install a GPU driver.
 |
| CFYUSEU Crypto Ethereum Miner Case with Barebone Motherboard |
- [GPU Mining Rig Rig Platform Settings] Motherboard: 8 cards, aligned to a distance of 70mm PCI-E; CPU: Inter1(R) Celeron-CPU 857; RAM: DDR3 4 GB; Hard Disk: 128G SSD-MSATA; Cooling fans: 8 fans 2500-4500rpm; USB: rear * 5; Network port: RTL8111E RJ45 Gigabit interface; Display interface: HDMI; AC power: one V110V-AV260V; Operating System: Linux / Windows / OS
- [8 GPU Support] There are 8 GPU expansion slots in the miner shell. The mining machine chassis supports 8 GPUs 3060TI/3070/6800/6800XT 6900/6900XT at the same time. However, only 4-6 30803090 units are recommended Note: GPUs larger than 12 inches are not available. Please keep about 300W of power.
- [Support 8 Fans & 2 Fan Controllers] The miner box is equipped with 8 fans. Four fans draw air while the other four blow in opposite directions to keep the GPU/motherboard/power supply cool. The fan controller can control the fan speed from 2500 to 4500 rpm.
- [5 USB Ports] Developed specifically for cryptocurrency mining - Litecoin, Dogecoin, Ethereum, Ripple, Zerocoin, etc. The mining box has 5 USB ports which are enough for daily work. Please make sure all interfaces are in good contact to avoid motherboard/GPU overheating.
- [Mining Equipment Status] The hardware does not have its own graphics processing unit (GPU) or power supply. Including: motherboard, processor, power switch cable, 128 GB SSD, 4 GB RAM, 2500-4500 rpm fan * 8, 6-pin cable on (6 + 2) pins * 8 pieces, packing screw * 15th.